Results 1 to 3 of 3

Thread: Cyclone Box, Download, Setup and First Steps for installation

  1. #1
    Product Supporter Sam-TheMaster's Avatar
    Join Date
    Aug 2010
    Thanked 64 Times in 46 Posts

    Thumbs up Cyclone Box, Download, Setup and First Steps for installation

    As on 7/7/2010
    1. Download final installer from: and Install it. While installing agree to install box drivers, etc.

    2. Connect box to PC. PC should detect new device - "Cyclone Bootloader". Simply do automatic driver installation, till installer installed them in Win32 INF already.

    3. Run Start -> Programs -> Cyclone Box -> Cyclone Box

    At bottom, you should see "Connected [Bootloader Mode]". That means your box was detected by software, and you can proceed with box registration - needed step to activate your box.

    4. Run Box Registration Wizard, click Prepare Box.

    Select your reseller from list, and fill all needed data.

    If you see "Box registration status: Registered OK" that means all passed ok. You can proceed with box activation.

    5. Run Box Maintenance Wizard, and click Maintenance box. In 1-2 minutes your box will be initialized.

    **** VERY IMPORTANT : During box upgrade, please DON'T disconnect your box, even if software may act as hang ! We use ciphering on few layers during upgrade, and if you have slower PC, decrypting RSA and other ciphers, may take quite more time !! And then, if you disconnect your box, it will not be upgraded. It is no problem, because it will not be damaged, but You will lose YOUR time and OURS time, asking for next update credit !!

    6. Your box is registered and activated. Now your security card needs be initialized. To initialize security card, box needs be activated! Run Security Card Manager. Read your card, and click Fill Credits. Box should change its mode to Cyclone Box and Windows should install new drivers again (same steps as for Bootloader). On bottom of screen you should see "Connected [Main Mode]".

    How to activate Super DCT4 in my box?
    It is very simple. Go to "Credits" module (same as you are using for calculating ASK/RPL), and click big "Activate SUPER DCT4" button. In seconds you should see similiar message:

    Started Super DCT4 Activation at 03:45:20
    Handling device: [Cyclone Team], [Cyclone Box]
    Service Tag: 4F67674F5428157448CEACEB547BC575
    Cyclone Server (, Cyclone Box Team 2008, 2009 - Ready.
    Super DCT4 Activated Successfully! Credits Left: 950
    Please, replug your box from USB now, and use Maintenance Function to upgrade it again.
    After next upgrade, box will be activated for Super DCT4 Functions!
    As message says, replug your box and re-upgrade it again. After re-upgrade your box is SUPER-DCT4-READY

    8. All is done. You can run DCT4/WD2/BB5 tool and check if necessary selftests will be passsed, so you can enjoy using your Cyclone Box One note: security card having 1000 credits at initialization. Each card operation tooks those credits, so after some time you need to reinitialize card (when counter reachs 0). This operation is of course free and realtime, using server.

     Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: Handling device: [Cyclone Team], [Cyclone Box] Initializing box... Box Firmware: Cyclone Nokia Application v01.45, (Jul  6 2010 19:20:51, gcc v4.3.2, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2010 wk27 Box Serial Number: C0000005 HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk32 Initializing security card... Card Serial Number: D0000001 Card Firmware Revision: 0108 Card is activated Box is activated Started box selftests procedure USB Voltage    4,99v    PASSED MCU Voltage    3,30v    PASSED Core Voltage    1,79v    PASSED VBAT Voltage    0,01v    PASSED VBAT Voltage    4,73v    PASSED Box VPP disabled VPP Voltage    0,02v    PASSED Internal Box VPP Enabled VPP Voltage    4,88v    PASSED Box VPP disabled VPP Voltage    0,00v    PASSED External Box VPP Enabled VPP Voltage    0,04v    FAILED - IGNORED - Probably power supply is not connected Box VPP disabled All box selftests passed! Super DCT4 Activation: TRUE Initializing FBUS... All initialized - Ready to work 
    Remember to check the Version of the software and the firmware of your Cyclone box
    Enjoy your box!

    Note : Mirror for installer and exe :

  2. # ADS
    Circuit advertisement
    Join Date
    Advertising world
    Official iPhone Unlock - iUnlockStore World's most trusted iPhone Unlocking Solution -
    Official iPhone Unlock

  3. #2
    Junior Member ayikobuam's Avatar
    Join Date
    Dec 2011
    Thanked 0 Times in 0 Posts

    Red face cyclone box installation

    after running the cyclone box installer and drivers installation i recieved a warning that 'can not find cyclonebox dll please re-install the application..'' it keeps repeating itself i install the application please help me on how to do this.

  4. #3
    Junior Member azhar930's Avatar
    Join Date
    Dec 2012
    A, A
    Thanked 0 Times in 0 Posts


    Great shearing good dear

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Details steps for samsung b119,b119new and b159
    By ComboUnlocker in forum Advance CDMA products
    Replies: 0
    Last Post: 08-25-2010, 09:19 AM
  2. FAQ + Setup Guide for ATF Box
    By AdvanceBox in forum Advance Box
    Replies: 5
    Last Post: 08-21-2010, 10:03 AM


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts